TPV、常平TPV供应厂家(在线咨询)、TPV食品级 TPV材料
倍韧/BESTPERNE® EN45A-HL
热塑性弹性体Thermoplastic Elastomer
产品说明Product description |
||||||||
·EN45A-HL是一款以SEBS为主基材的高性能弹性体,易加工,耐黄变,耐化学溶剂性能非常出色。 ·EN45A-HL is a kind of high performance thermoplastic elastomer based on SEBS as main material.Aslo it has excellent yellowing resistance and chemical solvent resistance properties.It is easy processing. |
||||||||
关键特性Key characteristic |
||||||||
1.表面哑,手感细腻柔软。Dumb surface, exquisite and soft touch 2.可粘接PP,强度非常高。Very high bonding strength, adhesive material:PP 3.成型快、不粘模具。Rapid molding,non-stick mold |
||||||||
功能Function |
||||||||
产品应用 Main application |
1 汽车用品 Automotive products |
3手把Handlebar |
||||||
2 运动器材Sports equipment |
4玩具产品Toy products |
|||||||
加工方法Processing method |
注塑成型Injection molding |
|||||||
环保认证 Environmental certification |
ROHS |
REACH |
EN71-3 |
|||||
PAHS |
ASTM-F963 |
Phthalate |
||||||
颜色Color |
本色 Natural |
|||||||
气味Smell |
少许树脂味A little resin smell |
|||||||
外型Appearance |
圆球形小颗粒Cylindrical particle,about 3mm×1.5mm |
|||||||
储藏期Storage period |
常温下通风干燥,24个月Ventilated dry at normal temperature,about 24 months |
|||||||
包装方式Packaging method |
25公斤/袋 25kg/bag |
|||||||
物理性能Physical properties |
结果Result |
单位Unit |
方法Method |
成型条件Molding condition |
||||
比重Specific gravity |
1.03±0.02 |
g/cm3 |
ASTM D792 |
干燥温度Drying temp 70℃ |
||||
硬度Hardness |
45±5 |
shoreA |
ASTM D2240 |
干燥时间Drying time 2Hours |
||||
拉伸强度Tensile strength |
>2 |
Mpa |
ASTM D412 |
射嘴温度Nozzle temp 190℃ |
||||
断裂延伸Elongation at break |
>400 |
% |
ASTM D412 |
螺筒一段温度Screw 1 temp 190℃ |
||||
撕裂强度Tearing strength |
>14 |
Kn/m |
ASTM D624 |
螺筒二段温度Screw 2 temp 180℃ |
||||
熔融指数Melt index |
>1 |
g/10min |
ASTM D1238 |
螺筒三段温度Screw 3 temp 180℃ |
||||
注意事项Matters need attention |
||||||||
清洗料管 Purge compound |
需使用PP或 PE清洗干净机台螺杆,且把机台射嘴彻底清除干净Please make sure you that you have cleaned the machine screw with PP or PE, and put the machine nozzle thoroughly clean |
为节省材料,将胶头量减至最低,现作出以下工作程序及洗机守则。
一. 啤够数、转模前、停机前务必关料斗,把炮筒内的TPE料啤完,直啤到螺杆不能回料为止
二. 换TPE料时务必将料桶的材料挖干净。
三. 啤黑色或深灰色材料射空胶时要把胶压小、压薄,可用的放在水口一起循环再用。
四. 水口、次品与不能循环再用的胶头务必分开装。
五. 保持机位卫生干净,尽量不让水口及次品掉到机底、地面、混杂、受污染。
六. 开啤前将模面油污、防锈油抹干净,避免次品受污导致不能循环再用。
七. 洗机前先将料斗内余料尘粉清理干净,再用洗机料清洗螺杆炮筒,有必要时加入螺杆清洗剂或洗衣粉。清洗将近完成前续渐调低炮筒温度避免炮筒螺杆内的料再度烧焦及熔化成液体引至开啤时不能回料。
八. 可以使用白色及透明PP来进行清洗。
十. 一般情况下啤白色后转啤灰色、黑色均不用洗机。
十一. 啤TPE时停机不超过15分钟,再啤时不用射空胶。试啤时将啤机熔胶量调至大约成品用胶量,射空胶三次即可开啤。
↵Copyright © 2021 广东塑伯新材料有限公司
All Rights Reserved. 粤ICP备2020127300号
销售热线:400-800-0302 手机:13602342196 电话:0752-6768128 传真:0752-6768088
地址:广东省惠州市博罗县石湾镇黄西工业园径二路 邮箱:sales@tpe-sp.com 网址:www.tpe-sp.com